Swing Gate Opener

Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board

Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board

Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board
Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock W/ Board. Popular Electromagnetic Lock for Swing Gates and Doors, is designed to provide extra security and stability to your gate opener system. They are suitable for various types of gates. It can work with swing gate opener to enforce the lock, especially for heavy windy days.

One set includes:1 Lock with 5 metre cable, 1 Lock recevier, 1 Clevis Pin, 1 Plug pin, 1 Spacer, 2 Lock key (manual release). Three Rolling Teeth: The Swing Lock requires a fraction of the force that outlines the industry standard for the closing of gate locks. It only requires 1 lb of force compared to the industry standard of 10 lbs.

This difference means that the gate can slow down to a lower speed and be latched with less force. The reduction of force puts less strain on the gate and the gate opener itself. Less strain leads to a longer lasting gate opener system and a reduced chance of damage to the gate. It has a small control board 12-24 Volt AC/DC powered relay, you can use it for other gate operator brands gate/garage door. The Automatic Lock unlocks and locks automatically as an electronic gate is activated to open and close (reliant on standard 12v gate outputs). Note: Electric lock improves the safety for your gate, and it is highly recommended if you have animals or live in areas affected by strong winds when the gate is longer than 1.5 meters (7ft). The Electric Lock Automatically Locks and Unlocks with Your Gate as it Opens and Close! The X-House electric gate lock automatically locks and unlocks the gate when the gate opener is activated. It is a perfect solution to add security for your single or dual gate, provide stability and additional protection for damaging forces, prevent breakages at a strong wind, and improve animals' safety.

Electric lock is strongly recommended when your gate is longer than 7 feet (1.5 meters). Suitable for all types of swing gates, and perfect for driveway gates made by steel, wood, vinyl, plastic and shaped as panel, tube, and chain-link. Work with most single or dual swing gate openers, as well as most 24V gate opener systems of other brands. It eliminates "wiggle room" between your gate/post, gate/fence, or gate/gate (in dual swing gate). The electric lock adds reinforcement to prevent against unwanted intrusion on gate systems.

Weather-resistant for all seasons of the year. Manual Keys are included to enable manual operating during power outage or when you lose the remote. Higher quality designed plastic-spraying surface makes the lock more durable and reliable. Small Control Board DS33A for multi garage door opener. This small control board 12-24 Volt AC/DC powered relay, you can use it for other gate/garage door operator brands. The Automatic Electric Lock unlocks and locks automatically as an electronic gate is activated to open and close (depend on standard 12V/24V gate outputs). The blue and white adjustable resistance on the board is used to adjust the delay time:The minimum is 2 seconds counterclockwise and the maximum is 6.5 seconds clockwise. When the door LOCK is working, the DS33A will power on, the relay absorbs and closes, and the delay begins. When the delay time reaches, the relay is disconnected. VCC : Connecting 12V/24V DC/AC on board power supply. GND : Connecting to the LOCK port on the Ground board (Reserved terminal). NO : Directly connected to the electric lock power line in parallel for switching. CM : Directly connected to the electric lock power line in parallel for switching. Automatic Electric Gate Lock for Swing Gate Operator Opener System AC/DC 12-24V. IP68 gland is used to protect the cable and strengthen waterproof! A keyed manual release can be used in case of power failure! Small control board for multi gate usage. Wiring the Lock to gate opener control boards with terminal. Remove the front end of the actuator that is attached to the gate bracket with a clevis pin and clip pin. Wire tie of clamp the front end on the gate to support it.

This will enable you to swing the gate manually while installing the gate lock. Please note that the front ends of both actuators need to be disconnected for dual gate systems. Swing the gate to the closed position.

Find the best position to mount the lock and the receiver. It must be level with the actuator. The lock should be mounted on a gate cross member or other solid part of the gate surface. Position the lock in an approximate mounting position on a cross member or other mounting surface that is level with the actuator.

The lock can be moved into an exact position later in the installation process. Find a location on the fence post level with the gate lock and temporarily tie the lock receiver provided. Slide the gate lock back and forth until it lines up with the receiver. The pin holes on the receiver must line up with the slot in the lock. Once this position is achieved, mark the post through the center of the two slots in the receiver. The gate lock must now be permanently mounted to the gate cross member or gate surface. Make sure that the lock is aligned with the receiver and mark holes on the gate through the upper and lower slots on the lock. Drill holes through the marks and attach the lock to the gate surface with the appropriate hardware. Do not use bolts greater than 5/16 inch diameter as they will not It through the slots. Insert the clevis pin through the holes in the receiver and hammer the locking cap onto the bottom of the pin. NOTE: It may be easier to remove the receiver from the post and then hammer the pin into the blocking cap on a hard surface. Then the receiver can be remounted to the post. Chain drive garage door openers. We offer the best prices around on high quality products. Our E-store includes media such as books, movies, music and games while offering electronics, toys, sporting apparel, clothing, tools, general home, garden items and more.

We are always working hard to ensure your package arrives as soon as possible. We do not accept P. Please provide a physical address. We try our very best to make sure every customer is completely satisfied.

If there's a problem, message us! We're happy to help. This item is in the category "Home & Garden\Home Improvement\Building & Hardware\Garage Doors & Openers\Opener Systems".

The seller is "summerstore_235" and is located in this country: US. This item can be shipped to United States.

  • Color: Automatic Electric Gate Lock
  • Special Feature: Waterproof
  • Color Name: Automatic Electric Gate Lock
  • Form Factor: Case
  • Compatible Phone Models: HTC
  • UPC: 7445018786769
  • EAN: 07445018786769


Automatic Electric Gate Lock for Swing Gate Opener Automatic Gate Lock With Board